O'Brill Company

Construction Specialty Suppliers

       6626 N. Milwaukee Ave.

Niles, IL 60714

773-775-1122 or 847-647-0005

FAX 847-647-7819

Since 1967

Patch-Rite®     |    Products     |     Manufacturers     |     Price Guide     |     News

NO. 355-PD

LIN-SEAL EMULSION®

CURING AND SEALING COMPOUND

Technical Description
SEALTIGHT LIN-SEAL EMULSION Curing and Sealing Compound is a true water-base, high-solids solution of boiled linseed oil. When properly applied, it provides an impermeable seal which optimizes water retention.

LIN-SEAL EMULSION meets maximum VOC content limits of 700 g/L for Concrete Curing and Sealing Compounds as required by the U.S. EPA Architectural Coatings Rule.

Uses
SEALTIGHT LIN-SEAL EMULSION Curing and Sealing Compound is ideal for use in preventing the spalling and scaling of concrete surfaces. Use on bridge decks, parking garage decks, ramps or any concrete surface exposed to water, salts or other destructive substances. LIN-SEAL EMULSION increases the durability of concrete to prolong its life.

Advantages and Benefits

Application
SURFACE PREPARATION: Surfaces to be sealed must be clean and dry. Remove all dirt, oil, grease, curing compounds and other substances that would prevent the proper penetration of the sealer.

APPLICATION: Apply only in a temperature range of 40ºF to 95ºF (4ºC to 35ºC). Apply with a hand or powered sprayer. Broom off puddles or excess liquid. Old concrete should be treated annually.

COVERAGE: Apply at a rate of approximately 300 ft.²/gal. (7.36m²/L). A second application at approximately 600 ft.²/gal. (14.7m²/L) is recommended for increased protection and spall prevention.

CLEAN-UP: Use soap and water to clean tools and equipment. Materials soaked with linseed oil (rags, absorbants, etc.) may spontaneously catch fire if improperly discarded. Immediately after use, all materials coming in contact with this product should be placed in sealed, water-filled containers.

Packaging
5 gallon (18.93 liter) Pails
55 gallon (208.20 liter) Drums

Specifications
ASTM C 309*
AASHTO M 148*
State D.O.T. Specifications
Boiled Linseed Oil: ASTM D 260
Fed. Spec. TT-L-190-D
*With exemptions for drying time

Limitations/Precautions
DO NOT DILUTE. Do not use on densely troweled surfaces or on surfaces where darkening of the concrete is undesirable. KEEP FROM FREEZING. Refer to Material Safety Data Sheet for complete health and safety information.

This material last updated January, 2000.

W. R. MEADOWS, INC. warrants that, at the time and place we make shipment, our materials will be of good quality and will conform with our published specifications in force on the date of acceptance of the order. THE FOREGOING WARRANTY SHALL BE EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND ALL OTHER WARRANTIES OTHERWISE ARISING BY OPERATION OF LAW, COURSE OF DEALING, CUSTOM OF TRADE OR OTHERWISE. As the exclusive remedy for breach of this Warranty, we will replace defective materials, provided, however, that the buyer examine the materials when received and promptly notify us in writing of any defect before the materials are used or incorporated into a structure. Three (3) months after W. R. MEADOWS, INC. has shipped the materials, all our Warranty and other duties with respect to the quality of the materials delivered shall conclusively be presumed to have been satisfied, all liability therefore terminates, and no action for breach of any such duties may thereafter be commenced. W. R. MEADOWS, INC. shall in no event be liable for consequential damages. Unless otherwise agreed to in writing, no warranty is made with respect to materials not manufactured by W. R. MEADOWS, INC. We cannot warranty or in any way guarantee any particular method of use or application of the performance of materials under any particular condition. Neither this Warranty nor our liability may be extended or amended by our salesmen, distributors or representatives, or by our distributor's representatives, or by any sales information or drawings.

Send mail to webmaster@obrillcompany.com with questions or comments about this web site.
Copyright © 2002 O'Brill Company
Last modified: August 09, 2004