SEALTIGHT ULTRITE Degreaser is a heavy-duty
concrete degreaser and stripper which will biodegrade. It naturally and safely
replaces mineral spirits and chlorinated solvent type heavy-duty concrete
SEALTIGHT ULTRITE Degreaser penetrates concrete surfaces on contact to
soften, lift, and remove a wide range of oils, polymers, fats and greases. Use
ULTRITE Degreaser to remove dirt, tire marks, oil spills, grease and other
contaminants. It will also remove most curing compounds and sealants from
concrete floors. Periodic stripping of concrete floors is in keeping with good
concrete maintenance practices. It is ideal for use in warehouses, industrial
plants, food processing plants, schools, automotive plants, parking garages,
plazas and service stations...anywhere cleaning and stripping of concrete
surfaces is required.
Advantages and Benefits
|Both a stripper and a degreaser in one
|Ready and easy to use full-strength directly from the
Use only on masonry or concrete surfaces. Do
not use on painted surfaces. DO NOT ALLOW DEGREASER TO DRY OUT. See Step 2 under
Solubility in Water:
Rinsability with Water:
|Clear, Light Yellow
7.85 lbs. (.94 kg/L)
100% after proper dilution
|* NOTE: When
applied and rinsed per W.R. MEADOWS instructions, the material raised
from the surface will contain residual amounts of petroleum
hydrocarbons. These hydrocarbons are generally very low in concentration
and will not have a negative environmental impact on affected soils.
Material(s) removed by the SEALTIGHT ULTRITE Degreaser will need to
comply with local, state and federal disposal requirements.
1 gallon (3.8 liters) Units
5 gallon (18.93 liters) Pails
55 gallon (208.20 liters) Drums
Stripping/degreasing/heavy-duty cleaning: 100-200 ft.˛/gal. (2.5-4.9m˛/L).
One year in unopened, unused container.
Note: Application of SEALTIGHT ULTRITE Degreaser may depend on the type of
curing compound, oil or grease on the surface and in the pores of the concrete.
A typical application should be as follows:
Step 1: Apply ULTRITE Degreaser full strength from the container to remove heavy
dirt build-up, tire marks, oil spills, grease, hydraulic fluid and any other
difficult to remove contaminants from the concrete surface. For normal cleaning
applications and for removing curing compounds and cure and seals, apply full
strength to the entire floor.
Do not allow ULTRITE Degreaser in “as applied” form to spill or run off of
Step 2: Apply ULTRITE Degreaser and allow it to soften the coating or stain, but
DO NOT ALLOW THE SURFACE TO DRY. (Soak times vary, depending on the ambient
conditions and the degree of staining on the concrete.) In severe cases, it may
be necessary to apply additional ULTRITE Degreaser to remove stains and/or to
prevent the treated area from drying out.
NOTE: For severe oil and/or grease stains it may be
necessary to follow ACI Guide 515.1R (Section 3.4.2.) or the Portland Cement
Association (PCA) publication IS214T. These publications outline specific
instructions for stain removal, which can be followed by a SEALTIGHT ULTRITE
Degreaser application. (Copies of these articles may be obtained through your
local W.R. MEADOWS representative.
Step 3: With a stiff bristle brush or mechanical scrubber, thoroughly scrub the
Step 4: Rinse the area with large amounts of clean water. The cleaning action of
ULTRITE Degreaser may be evident by the very light whitish appearance of the
initial water rinse. Keep rinsing with water until there is no visible trace of
the product on the concrete. Disposal of rinse should follow all local, state
and Federal regulations.
Step 5: Test patch the dry concrete prior to painting or applying a subsequent
surface treatment. If necessary, clean the concrete floor with ULTRITE Degreaser
again until the desired results are achieved.
Clean all tools and equipment after use with water.
Safety & Toxicity
Combustible mixture. Keep this product away from heat, sparks and fire.
Can cause irritation of both skin and eyes. Wear rubber gloves and goggles at
all times. Harmful if swallowed. This product is for industrial and
institutional use only by trained personnel. Keep out of reach of children.
Refer to Material Safety Data Sheet for complete Health and Safety Information.
This material last updated April, 2000.
W. R. MEADOWS, INC. warrants that, at the time and place
we make shipment, our materials will be of good quality and will conform with
our published specifications in force on the date of acceptance of the order.
THE FOREGOING WARRANTY SHALL BE EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTY,
EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE AND ALL OTHER WARRANTIES OTHERWISE ARISING BY
OPERATION OF LAW, COURSE OF DEALING, CUSTOM OF TRADE OR OTHERWISE. As the
exclusive remedy for breach of this Warranty, we will replace defective
materials, provided, however, that the buyer examine the materials when received
and promptly notify us in writing of any defect before the materials are used or
incorporated into a structure. Three (3) months after W. R. MEADOWS, INC. has
shipped the materials, all our Warranty and other duties with respect to the
quality of the materials delivered shall conclusively be presumed to have been
satisfied, all liability therefore terminates, and no action for breach of any
such duties may thereafter be commenced. W. R. MEADOWS, INC. shall in no event
be liable for consequential damages. Unless otherwise agreed to in writing, no
warranty is made with respect to materials not manufactured by W. R. MEADOWS,
INC. We cannot warranty or in any way guarantee any particular method of use or
application of the performance of materials under any particular condition.
Neither this Warranty nor our liability may be extended or amended by our
salesmen, distributors or representatives, or by our distributor's
representatives, or by any sales information or drawings.