Physical Properties

TEST Penetration, non-immersed @ 77ºF (25ºC) Penetration, fuel immersed @ 77ºF (25ºC) Flow, 72 hours @ 158ºF (70ºC) Bond, @ 0ºF, 3 cycles, 50% extension Bond, non-immersed Bond, water-immersed Bond, fuel-immersed Change in mass, fuel-immersed

RESULTS 11.0mm 11.0dmm No flow Pass 3 cycles No cracks or sep. No cracks or sep. No deeper than 0.25m -1.0

SS-S-1614A 13.0mm max. 15.5mm 30mm Pass 3 cycles No cracks or sep. No cracks or sep. No crack deeper than 0.25" (6.35mm) 2.0% maximum

Additional POLY-JET 1614 Use Properties

Recommended pour temperature Safe heating temperature Weight/gallon Coverage 1/2"x1" (12.7x25.4mm) joint

250ºF (121ºC) 270ºF (132ºC) 9.89 Ibs./gallon (1.19 kg/liter) 26 lbs. per 100 lineal feet (380 g/m)

Application
While heating, the sealant will go through a phase change in its viscosity, starting out thin and becoming quite thick between 180ºF (82ºC) and 225ºF (107ºC) as the polymers crosslink. Above 225ºF (107ºC), the sealant will thin back down to a pourable viscosity. Do not exceed the safe heating temperature [270ºF (132ºC)] as this will significantly reduce the pot life of the material and may cause the material to convert to a solid. If this should occur, the sealant must be removed from the melter immediately. (NOTE: POLY-JET 1614 cannot be remelted once it has cured to its solid form.) At the safe heating temperature, the application life is a minimum of 6 hours.

SEALTIGHT POLY-JET 1614 must be heated in an oil-jacketed melter-applicator equipped with an agitator and separate temperature thermometers for the oil bath and heating vat. Heat only sufficient material to be used the same day. Material may be added as the sealant is withdrawn only if application is stopped and material is allowed to go through a heating cycle. Sealing may be done at air temperatures of 40ºF (4ºC) or higher. (NOTE: Application of sealant into frozen or wet pavement will result in loss of bond and premature failure of the sealant.) At the end of each day's sealing operation, all remaining material must be drawn off.

SEALTIGHT POLY-JET 1614 is not compatible with asphalt-based joint sealants. All equipment should be thoroughly cleaned prior to use. If flushing oil is used, drain all remaining flushing oil from the equipment including the kettle, pump, lines and hoses.

JOINT PREPARATION: Suggested joint configuration is a 2:1 ratio of 1/2" (12.7mm) minimum width formed by sawing, cleaning by sandblasting, blowing dry with oil-free compressed air, and installation of CERA-ROD Heat-Resistant Backer Rod. Joint interfaces must be dry and free of dust. Fill sealant flush with the pavement surface and strike off clean.

MAINTENANCE SEALING: Old joint sealing material must be routed out of the joint to a depth of 1 to 1-1/2" (25.4 to 38.1mm). Interfaces must be cleaned by sawing, sandblasting or mechanical abrasion. CERA-ROD Heat-Resistant Backer Rod should be installed to form a 1:1 ratio reservoir. In no case should the width to depth exceed a 2:1 ratio.

Packaging
The sealant is packaged in an easy-to-use poly bag inside a 5 gallon (18.93 liter) pail. Both the sealant and bag are to be placed in the melter for heat-up. One pallet of sealant contains 36 pails.

Limitations and Storage
Do not exceed the safe heating temperature of 270ºF (132ºC) or polymer degradation and gelation may occur. SEALTIGHT POLY-JET 1614 cannot be remelted and should not be left in the melter after heating. The kettle should be flushed completely clean at the end of the sealing run. SEALTIGHT POLY-JET 1614 is not compatible with asphalt and cannot be used in conjunction with asphaltic concrete pavement or asphalt-impregnated expansion joint fillers. SEALTIGHT POLY-JET 1614 is not intended to be jet-blast resistant except when aircraft are moving at minimum moderate speeds.

Do not store the sealant in direct sunlight. Storage temperature should not exceed 100ºF (38ºC).

Precautions
Direct contact with this product should be avoided. The use of safety goggles/glasses, chemical-resistant gloves and protective clothing is recommended. Breathing of fumes/vapors should also be avoided. Use of a NIOSH-approved vapor/mist respirator is recommended. Refer to MSDS for details.

W. R. MEADOWS, INC. warrants that, at the time and place we make shipment, our materials will be of good quality and will conform with our published specifications in force on the date of acceptance of the order. THE FOREGOING WARRANTY SHALL BE EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND ALL OTHER WARRANTIES OTHERWISE ARISING BY OPERATION OF LAW, COURSE OF DEALING, CUSTOM OF TRADE OR OTHERWISE. As the exclusive remedy for breach of this Warranty, we will replace defective materials, provided, however, that the buyer examine the materials when received and promptly notify us in writing of any defect before the materials are used or incorporated into a structure. Three (3) months after W. R. MEADOWS, INC. has shipped the materials, all our Warranty and other duties with respect to the quality of the materials delivered shall conclusively be presumed to have been satisfied, all liability therefore terminates, and no action for breach of any such duties may thereafter be commenced. W. R. MEADOWS, INC. shall in no event be liable for consequential damages. Unless otherwise agreed to in writing, no warranty is made with respect to materials not manufactured by W. R. MEADOWS, INC. We cannot warranty or in any way guarantee any particular method of use or application of the performance of materials under any particular condition. Neither this Warranty nor our liability may be extended or amended by our salesmen, distributors or representatives, or by our distributor's representatives, or by any sales information or drawings.