Fast setting, pourable and self-leveling makes it ideal for saw cut joints
	As a semi-rigid filler, it protects slab edges from spalling, yet allows sufficient flexibility for interior slabs

Limitations
Do not use in vertical or sloping joints, or in areas subject to continuous water immersion. Do not use in joints designed for any significant movement (i.e. expansion or contraction joints). Do not apply when concrete temperature is below 40ºF (4ºC). This product is recommended for interior use only. It is not suitable for areas subject to sudden extreme temperature changes. Concrete must be a minimum of 28 days old prior to installation.

Color
Gray

Shelf Life
2 years

Packaging
1 gallon (3.79 liters) Unit

Coverage
231 inch³ (3,785cm³) per unit

PHYSICAL PROPERTIES

Typical Physical Property	Test Method	ACI Report 302.1	Typical Value
Solids % by weight Mix Ratio (A:B) Color (A & B mixed) Consistency Pot Life (1 gal. unit), minutes Thin film tack-free time, hours Tensile adhesion to concrete: @ RT (3 days), psi @ 40ºF (4.4ºC),(3 days), psi Hardness, Shore D (3 days) Tensile strength:@ RT (3 days), Tensile strength:@ RT (7 days),psi Elongation: @ RT (3 days), % Elongation: @ RT (7 days), % Water Absorption: @ RT (24 hr.), % by weight Shrinkage	ASTM D 1259 by volume visual Appearance ASTM C 881 ASTM C 879 ASTM D 5329 ASTM D 2240 ASTM D 638 ASTM D 638 ASTM D 638 ASTM D 638 ASTM D 570     ASTM D 2566	100 min. 50 min. 6 min.	100 1:1 Gray Pourable 20 3.5   290 880 53 660 770 72 53 0.56 Negligible

LINEAL FEET PER UNIT
Joint Depth 1" 1-1/4" 1-1/2" 1-3/4" 2"	Joint Width 1/8" 154 123 102 88 77	3/16" 102 82 68 58 51	1/4"  77 61 51 43 38
LINEAL METERS PER UNIT
Joint Depth 25mm 32mm 38mm 44mm 51mm	Joint Width 3mm 50 meters 39 meters 33 meters 29 meters 25 meters	6mm 25 meters 20 meters 17 meters 14 meters 12 meters

Joint Design
Joint frequency, width and depth shall be as specified by the design engineer. It is suggested that the width of a typical saw cut shall be 1/4" (6.4mm) maximum and the depth 25% of the slab thickness, but no less than 1" (25.4mm).

Application
JOINT PREPARATION: Joints must be level, clean and free of frost and standing water. Remove curing compounds, form release agents, old sealant and/or contaminants from joint surfaces by sandblasting or mechanical abrading. Blow any dust, dirt and laitance out of the joint with oil-free compressed air prior to application. To prevent run out from cracks in the bottom of joints, apply a small amount of fine dry sand. Install full depth. Do not use with soft backer rod.

MIXING: Mixing ratio is 1:1 by volume. DO NOT DILUTE. Prior to mixing, condition both components to 60º to 85ºF (15.5º to 29.5ºC). After conditioning, de-rim both cans and mix all of component “B” with component “A” (being careful to scrape the sides and bottom of both containers to ensure removal of all material). Mix for 2 to 3 minutes to an even color. Use as soon as possible.

Pot Life varies with temperature. At higher temperatures, pot life is shorter, while at lower temperatures, it is longer. Mix by hand or variable low-speed drill (400-600 rpm) using a paint mixing paddle. Mixed material must not contain streaks or lumps. Product container provides complete information. Read and follow all instructions and precautions.

DISPENSING: Pour mixed material directly from the can. Best results are obtained using a closed barrel caulking gun. Fill joint to within 1/2" of the top and allow to settle. Within 15 to 30 minutes, apply a second layer flush with the floor, checking occasionally for low spots (due to seepage) or overfill the joint. Allow the material to cure until it is almost solid, then shave, grind or sand off the excess to the desired floor level.

CLEANUP: Prior to solidification, clean all tools and equipment with Toluene or Xylene. Spilled material must be collected with absorbent material and disposed of in accordance with local, state and Federal regulations. Remove solid material mechanically.

Precautions
All skin areas should be protected by clothing and gloves, as some persons may develop a skin rash from contact. Base components or mixed, uncured material, can produce irritation of the eyes. In case of eye contact, immediately flush thoroughly with water for at least 15 minutes. Seek immediate medical attention. Wash skin with soap and water if contact with skin is made. Do not use solvents.

See Product Material Safety Data Sheet for additional information.